基于响应面法优化糙米速食粥加工工艺

为综合利用糙米，开发糙米全谷物食品，以糙米为原料，在单因素的基础上，研究煮沸时间、浸泡时间以及蒸煮时间等工艺参数对糙米速食粥复水性、感官品质以及糊化度的影响。以感官评分为响应值，采用响应面法对煮沸—浸泡—蒸煮法生产糙米速食粥的生产工艺进行优化，得到糙米速食粥的最优工艺参数为：煮沸时间20.40 min、浸泡时间1.46 h、蒸煮时间54.22 min，在此条件下糙米速食粥的感官评分为78.98，糊化度为85.28%。经验证试验，得到的结果接近预测值。通过质构分析可知，煮沸—浸泡—蒸煮法得到的产品要优于非浸泡法，复水后不易老化回生。本研究生产的糙米速食粥香味浓郁，品质较好，为糙米食品的工业化生产提供有益参考。     

利用响应面法优化椰子风味发酵乳加工工艺

本文以脱脂乳和椰浆为原料进行风味发酵乳的制备。以感官评定为指标,在单因素试验的基础上,选取UHT椰浆添加量、发酵温度和发酵时间进行试验,利用响应面法对椰子风味发酵乳的最佳配方进行优化。结果表明,对风味发酵乳的影响程度最大的因子是UHT椰浆添加量,其次为发酵时间。椰浆发酵乳的最佳配方为椰浆添加量16.5%,发酵温度45℃,发酵时间8h。以此配方制成的椰浆发酵乳,感官评分为45.56,产品颜色均匀,口感顺滑细腻,有浓郁的奶香、椰香风味和滋味。     

长江下游农区金花菜叶蛋白提取工艺优化及关键参数特征

为改进和优化金花菜(Medicago polymorpha)叶蛋白提取的工艺环节,并提高叶蛋白提取率及提取物纯度等参数指标,本研究选择长江下游农区广泛种植的金花菜为原料,通过设置较为合理科学的料液比、提取温度、加热时间、pH以及提取剂(酸)种类进行叶蛋白提取单因素试验。结果表明:各单因素试验最佳参数分别为料液比1∶3、提取温度70℃、加热时间15 min、pH 4、提取剂(酸)为盐酸。基于清洁安全生产角度,选择了单因素试验中提取指标同样较高的柠檬酸作为提取剂,设置了料液比、pH及提取温度的3因素3水平响应面试验,发现影响叶蛋白提取率的因素依次为pH、提取温度、料液比。得到最佳提取工艺:料液比1∶3、pH 4.1、提取温度72℃,相应的叶蛋白提取率为49.63%,提取物纯度为56.87%。本研究优化的技术工艺及相关参数指标可为农区豆科草类植物多元化利用及叶蛋白工业化生产提供一定的技术支撑和相关借鉴。     

芒果皮渣多糖提取工艺优化及其抗氧化活性研究

以芒果皮渣为原料,采用热水浸提法,在单因素试验的基础上,通过响应面法优化芒果皮渣多糖的提取工艺,同时分析芒果皮渣多糖的最佳沉淀条件,并利用清除ABTS+·、DPPH·和·OH能力评价其体外抗氧化活性。结果表明,芒果皮渣多糖的最佳提取及醇沉工艺条件为:浸提温度98℃,浸提时间4 h,料液比1∶40(g/mL),在此条件下芒果皮渣多糖提取率为9.29%。芒果皮渣多糖最佳醇沉工艺为:浸提次数3次,浸提液浓缩5倍,4倍体积95%乙醇醇沉6 h。体外抗氧化试验表明,芒果皮渣多糖对ABTS+·、DPPH·和·OH均有一定的清除效果,随着芒果皮渣多糖质量浓度的增加清除能力逐渐增强,当多糖浓度为1.0 mg/mL时,其对ABTS+·、DPPH·和·OH的清除率分别达到42.58%、92.37%和41.59%,此时还原力为1.49。     

Assessment of Vein Diameter and Body Surface Temperature after High-Intensity Laser Therapy (HILT) on the Tarsal Joint in Healthy Horses

The aim of the study was to assess the influence of high-intensity laser therapy (HILT) on vein diameter and on body surface temperature changes in the tarsal joint area in a group of clinically healthy racehorses. The hypothesis of the study was that HILT increases vein diameter and body surface temperature in healthy tissue. The study involved 16 Thoroughbreds being subjected to ultrasonographic examination to assess changes of diameter of the cranial branch of the medial saphenous vein and thermographic examination to indicate temperature change of the dorsal surface of the tarsal joint, just before and immediately after HILT treatment. Vein diameter and mean surface temperature of the tarsal joint significantly increased after HILT treatment. In addition, the study was the first to describe the photothermal effect of HILT in healthy horses. More studies are necessary to specify the parameters of the procedure, that is, wavelength, energy density, or time of the procedure, depending on the patient’s individual characteristics and type of tissue.     

无溶剂法制备丙烯海松酸蔗糖酯及其在空气-水界面吸附行为研究

在无溶剂条件下,以丙烯海松酸和蔗糖为原料,在高温熔融状态下通过酯化反应制备了丙烯海松酸蔗糖酯,运用红外光谱、核磁共振和凝胶渗透色谱对其结构进行了表征,并测试了其临界胶束浓度(CMC),利用再定向理论分析了丙烯海松酸蔗糖酯表面活性剂在空气-水界面的形态转变和吸附量等吸附行为。研究结果表明:成功合成了丙烯海松酸蔗糖酯,其CMC值为2.2 g/L。丙烯海松酸蔗糖酯在空气-水界面的吸附状态分为状态1和状态2,随着表面压的增加,溶剂摩尔分数逐渐降低,2种状态丙烯海松酸蔗糖酯分子在空气-水界面上的摩尔分数之和逐渐增加。计算了吸附在界面上的状态1和状态2丙烯海松酸蔗糖酯的吸附量,随着表面压增大,状态1吸附量先增大后减小,状态2吸附量占主导且持续增多,吸附量最高可达1.9 mmol/m2。丙烯海松酸蔗糖酯的吸附和胶束化摩尔自由能(ΔG)分别为-20.67和-15.16 kJ/mol,表明丙烯海松酸蔗糖酯优先吸附在界面上,达到饱和后就形成胶束。     

湿法机械处理改善粘胶级竹溶解浆反应性能的研究

为提高溶解浆进行粘胶纤维产品生产的加工性能及减少二硫化碳的排放，采用PFI（papirindustriens forsknings institut）磨打浆和瓦利打浆机打浆这2种湿法机械处理，以改善竹溶解浆的反应性能。以预水解硫酸盐法竹溶解浆为原料，考察PFI磨打浆及瓦利打浆机打浆对溶解浆反应性能及纤维形态的影响，并对同等打浆度条件下的2种湿法机械处理的效果进行比较。PFI磨和瓦利打浆机分别在打浆度为60.5°SR（15 000 r）及36.4°SR（30 min）的优化工艺条件下，Fock反应性能从68.3%分别提高到73.2%和84.0%，粘胶过滤性能由“不通过”到粘胶过滤值分别为3 196.1 s和2 115.6 s。同时，上述2种处理方式均使纤维粗度和长度下降，细小纤维含量、比表面积和总孔隙量增加，且使聚合度损失小。同等打浆度条件下，基于瓦利打浆机对纤维更多的剪切行为，瓦利打浆机打浆对反应性能的提高效果更为显著。     

滴灌模式和水分调控对夏玉米干物质和氮素积累与分配及水分利用的影响

采用裂区试验设计探究了地下滴灌和地表滴灌(drip underground, DU; drip surface, DS)模式下土壤水分调控(分别为田间持水量的40%～50%、60%～70%和80%～90%,记为W40、W60和W80)对夏玉米干物质和氮素积累与分配及水分利用效率的影响。结果表明,DU处理的吐丝后氮素积累量及水分利用效率分别较DS显著提高了6.18%和4.85%～8.61%。夏玉米的干物质、氮素指标及产量对滴灌模式的响应依赖于土壤水分调控水平,在W40和W60处理条件下,DU处理显著增加夏玉米的净光合速率,提高了吐丝后干物质和氮素的积累量及向籽粒的转运,最终DU处理的干物质积累量、籽粒氮素积累量、产量及氮肥偏生产力分别提高了3.29%～19.94%、?1.10%～20.65%、3.29%～19.94%和3.31%～23.64%。而在W80处理条件下, DS处理的干物质积累量、吐丝后氮素积累量、产量及蒸散量比DU处理分别提高了6.80%～12.24%、5.93%、8.39%～14.91%和9.73%～14.57%。综上所述,在限水灌溉条件下,地下滴灌能够增加吐丝后干物质积累量、氮素积累量及其对籽粒氮素的贡献率,最终增加产量。在充分供水条件下,地表滴灌更有利于干物质及氮素的积累,但由于消耗过多的水分,因此水分利用效率未显著增加。     

Simulation of future dissolved oxygen distribution in pond culture based on sliding window-temporal convolutional network and trend surface analysis

Dissolved oxygen (DO) is a key ecological factor to measure the quality of water in the aquaculture. As the pond water body is affected by the breeding environment, the spatial distribution of DO shows a certain law in the entire pond. Therefore, to simulate the distribution of DO in aquaculture waters and grasp the temporal and spatial variation of DO is the key to achieving precise regulation of DO. For this purpose, this paper proposed a method for simulating the temporal and spatial distribution of DO in pond culture based on a sliding window-temporal convolutional network together with trend surface analysis (SW-TCN-TSA). This paper first utilized SW to construct DO data sets with different prediction durations, and then used the improved TCN model to realize one-dimensional time series prediction for DO at single monitoring point. Based on the prediction results of DO, a TSA method was performed on the predicted values of DO at the extreme moments of all discrete monitoring points, so as to realize the simulation of the temporal and spatial distribution of DO in the pond. Experimental results show that the SW-TCN model has better prediction performance for one-dimensional time series prediction of DO. Compared with traditional deep networks, such as CNN, GRU, LSTM, CNN-GRU and CNN-LSTM, the values of evaluation indicators (MSE, MAE and RMSE) have been greatly improved. In the process of trend surface fitting, all fitting R² of DO at different water depths are higher than 0.9, indicating that the TSA can accurately reflect the temporal and spatial distribution of DO. This method can provide a basis for the prediction and early warning of DO in the three-dimensional space of the pond and has high practicability in aquaculture.     

单叶刺槐半同胞子代叶片的滞尘能力及叶表SEM特征分析

以单叶刺槐母本(A1-1)及6个叶形产生明显变异的半同胞子代无性系(A20-5、B24-3、C24-2、B23-1、C24-1、C23-1)新鲜叶片为材料,测定各样本的单位叶面积总颗粒物滞留量、颗粒物粒径分析及叶表微观结构SEM特征,通过相关性分析,筛选与滞尘能力相关的叶形及SEM指标,运用隶属函数法,依据各样本滞尘指标的隶属度均值对滞尘能力进行综合评价。结果表明:子代B23-1对空气中总颗粒物的滞留能力最强,C24-1对PM2.5的滞留能力最强,A20-5对PM2.5-10及PM>10的滞留能力最强;部分叶形及SEM特征指标与滞尘指标之间存在显著相关性;综合评价滞尘能力,全部样本可分为4类,第Ⅰ类为B23-1,滞尘能力强;第Ⅱ类为C24-1,滞尘能力较强;第Ⅲ类包括母本、A20-5、C23-1、C24-2,滞尘能力中等;第Ⅳ类为B24-3,滞尘能力相对较差。